Form Fill Seal Film

FFS Line-Fit & Roll Spec Guide

FFS Line-Fit & Roll Spec Guide

Most film enquiries begin with a bag size; this one begins with the machine. Before you order form fill seal film, read six variables straight off your line — flat film width, thickness band, core and roll build, unwind direction, gusset depth and anti-slip strip — and match them against the published ranges set out below. Each section expands one variable and closes with the single decision it drives, so the polyethylene film roll you specify arrives wound and slit for the forming tube already bolted to your machine.

400–760 mm Flat roll width (A + 2D)
0.07–0.24 mm Film thickness range
≤ 1500 mm Roll diameter
FFS Film Rolls, Jiangmei Packaging, Polyethylene FFS Film Rolls - FFS Film Roll Supplier

What the roll does between loading and roll change

The bag is made on the line, not bought pre-made. This is the order in which the stations run, and the one fit variable each station depends on — which is why the sections after this one are organised the way they are.

1

Roll loading

Core & roll diameter
2

Tube forming

Flat film width
3

Bottom seam

Thickness band
4

Filling

Gusset depth
5

Top sealing

Thickness band
6

Cut free

Even unwind tension
7

Roll change

Roll build & unwind

The longitudinal seam is formed first, before the bottom seam closes the tube. That sequence is why flat film width is settled first in any enquiry: it decides the tube, and the tube decides everything downstream.

Forming tube → flat film width

The roll width is not a preference. It is the number that makes the tube close around the gusset, and it is calculated as bag width plus both gussets.

Flat film width = A + 2D

A = finished bag width · D = gusset depth on each side. The published roll width band is 400–760 mm.

Bag width (A) Gusset (D each side) Flat film width (A + 2D)
380 mm 40 mm 460 mm
420 mm 50 mm 520 mm
450 mm 60 mm 570 mm
500 mm 60 mm 620 mm
520 mm 80 mm 680 mm
560 mm 100 mm 760 mm

Worked example

  1. Finished bag width A = 450 mm; gusset depth D = 60 mm on each side.
  2. Double the gusset: 60 × 2 = 120 mm.
  3. Add it to the bag width: 450 + 120 = 570 mm flat film width.
  4. 570 mm sits comfortably inside the 400–760 mm band, so the tube, the bag and the roll width agree.
  5. Send 570 mm together with the core size and the unwind direction, and the roll can be slit and wound for the tube you already run.

Where to find the number: the product page asks for the forming tube and flat film width, and suggests a photo of the machine plate. If the plate is unreadable, take the flat film width from the roll currently on the spindle and check it against the bag it produces. Decision point: if your calculated flat width falls outside 400–760 mm, the tube or the bag format has to change before a roll is ordered.

FFS Film Rolls, Jiangmei Packaging, roll wound for a form fill seal line
Rolls are wound and slit to the width and roll build the machine is set up for, rather than to one stock size.
FFS Film Rolls, Jiangmei Packaging, Polyethylene FFS Film Rolls - FFS Film Roll Supplier
Heavy-duty packaging film supplied on cores, wound for steady unwind from the first metre to the last.

Unwinder, core and roll build

Everything in this section sits behind the film rather than in the bag geometry. Get it wrong and the line still runs — it just drifts, and the seal position moves with it.

Core size

Confirmed per order. The spindle takes a set core size, so the core travels with your enquiry rather than with a stock list.

Roll diameter

Up to 1500 mm. A larger roll means fewer roll changes per shift — provided the spindle and shaft will carry the weight.

Unwind direction

Over-unwind or under-unwind: confirm which film face runs outward, so the film meets the forming shoulder the way your line expects.

Even tension

Wound for steady unwind, holding tension from the first metre to the last, so bag length and seal position stay consistent through a shift.

Decision point: send the machine make and model, the spindle core size and your maximum roll weight together. If your unwinder cannot take a 1500 mm diameter roll, the usable roll length per change is set by weight, not by diameter — and that is a winding instruction on the order.

Thickness band and the seal window

The published range runs from 0.07 mm to 0.24 mm, but the number that matters is narrower: the band your sealing jaws and forming shoulder are already set for.

What the line is set for

Jaws and the forming shoulder are configured for a range of film thickness, not a single figure. The product page asks buyers to confirm that band and to stay inside it.

What to send

The thickness band from your line specification, the product you are packing, and the bag weight the seam has to hold. That is enough to place the order inside the band.

Why it is a pre-order question

Film chosen outside the jaw set turns a routine order into a setting-up job on the line. Settle the band with the line supplier before a trial roll is wound.

Where it acts

Thickness drives the bottom seam and the bag-mouth seal. Polyethylene welds to itself cleanly under heat and pressure, and stays flexible at the required thickness so the filled pack settles on a pallet without stressing the seam.

FFS Film Rolls, Jiangmei Packaging, Industrial Packaging Films on core
Thickness is agreed against your line specification; the roll is then wound to that band.

Gusset depth and anti-slip strip

Two variables that are easy to leave until last, and both of which change the roll you need rather than the machine you have.

Gusset depth (D) up to 100 mm

A gusset opens the bag into a block that can stand on a pallet. It also feeds straight back into the width calculation — each gusset adds its depth into A + 2D, so increasing D from 60 mm to 100 mm on a 560 mm bag takes the flat film width to the top of the 760 mm band.

Anti-slip strip width (E) and spacing (F)

Both are made to customer requirements. The specification therefore comes from your palletising pattern and how the stacked packs have to behave in the warehouse — not from a catalogue default.

Decision point

Fix the gusset before you fix the roll width. If the gusset changes after the film is slit, the roll is the wrong width, even though the machine never moved.

Scenario to specification: what changes what

Most replacement-film orders start from one of these situations. Find yours, and the table tells you which variable moves and what to put in the enquiry.

Your situation Variable it moves What to send or confirm
A new forming tube has been fitted Flat film width Recalculate A + 2D and check the new figure sits inside 400–760 mm before ordering.
Bag weight is going up on the same line Thickness band and roll build Confirm the jaw set for the new thickness and the maximum roll weight the spindle will carry.
Several bag sizes run on one machine Roll build Ask for rolls wound and slit per size; core size stays constant while roll length and weight are confirmed per order.
Film tracks to one side at the shoulder Unwind direction Confirm over-unwind or under-unwind and which film face runs outward.
Filled bags do not stand squarely on the pallet Gusset depth Specify a gusset up to 100 mm and re-check the resulting flat film width.
Stacked packs shift in the warehouse Anti-slip strip Specify strip width (E) and strip spacing (F) to suit your palletising pattern.
The filling station is manual or semi-automatic Line type FFS film is built for high-speed fully automatic cycles; the product matrix below shows open-mouth and tubular bag formats for other lines.

What sits behind the specification

The fit numbers above are only useful if the film underneath them is built for a continuous automatic cycle — and if it is supplied to order rather than off a shelf.

Construction

  • Made from PE, LLDPE and HDPE with functional additives.
  • Produced by three-layer co-extrusion blown molding, with customized in-line printing.
  • Heavy-duty packaging film, supplied on cores for automatic form-fill-seal lines.
  • Polyethylene welds to itself cleanly under heat and pressure, which is what makes bag-mouth sealing possible at line speed.

Supply model

  • Wound and slit to the width and roll build your machine is set up for, not to one stock size.
  • One roll replaces a bag inventory: the bag is formed on the line, so film stock replaces pallets of pre-made bags in several sizes.
  • Suited to granular and powdered solids — fertilizers, chemicals, plastic resins and food ingredients.
  • Roll width, film thickness, core size, roll length and weight and pallet packing are all agreed per order.

Send these seven data points for a wound-to-line quote

There is no cart on this product: every roll is wound and slit against a machine, so the purchase path is a quote request. The enquiry that gets answered fastest carries the fit data with it.

  • Machine make and model — a photo of the machine plate is ideal
  • Forming tube and flat film width (A + 2D)
  • Core size taken by your unwinder spindle
  • Maximum roll diameter and roll weight your unwinder accepts
  • Unwind direction — over-unwind or under-unwind
  • Thickness band your jaws and forming shoulder are set for
  • Gusset depth, plus anti-slip strip width (E) and spacing (F)

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

Why Do FFS Film Rolls Need Gussets for Bulk Powder Packaging?

Gussets are the inward side folds in tubular FFS film, and they decide how a powder-filled bag takes shape, holds its volume, and sits on a pallet.

Read article

LLDPE and HDPE Differ in Heavy-Duty FFS Film Rolls

LLDPE and HDPE bring different kinds of toughness and stiffness to heavy-duty FFS film, and the useful question is how those traits are balanced in the finished roll.

Read article

Tubular FFS Film Compared with Pre-Made Open-Mouth Bags for Bulk Solids

Both formats put bulk solids into a bag, but one builds the bag during the filling cycle while the other arrives finished and waiting.

Read article

Frequently Asked Questions

What information is shown for this product?

Review the product details, images, and specifications presented on the official product page.

Where can i check the intended application?

Use the application and use-case information published on the official product page.

Which specifications should i confirm before ordering?

Confirm the specifications and options listed for the exact product variant before placing an order.

Where can i check available options?

Check the official product page or ask the supplier about options shown for the selected product.

How can i request product information?

Use the official contact or inquiry path provided on the site.

What should i include in an inquiry?

Include the product page, intended use, required quantity, and any specifications you need the supplier to review.

contact us
Name*
Email*
Message*
Verification Code*
Click to verify