Custom Packaging: Plate Fees, Samples & MOQ | Jiangmei

Customization and Prototyping Guide

Customization & sampling

Customization, plates and samples — from artwork to running production.

What a custom or printed order actually involves before the line starts: the route from artwork to engraving to sample, what the factory can and cannot take on, the minimum quantity, who carries the plate and tooling cost, and the four documents needed before a sample is made.

  • Applies to printed and made-to-size items
  • 5 sections · 14 terms
10 t Film & cold-stretch sleeve MOQ
20,000 Bag minimum, per order
8 Steps, new design to production
4 Documents before a sample

How to use this page Customization limits differ by product — what a film line can print is not what a bag line can print. This page states the rules that hold across the factory; the exact boundary for size, color count, structure and material is stated on that product's page, and is confirmed again in the quotation for the item you ask for.

The customization route

Two entry points — a design that has never been plated, and a repeat of one that has.

New customer · new design

Artwork or a sample bag is developed into a printing cylinder before anything is produced. Allow for artwork review, your approval of the proof, and engraving ahead of the order.

Existing customer · repeat order

When the artwork and the cylinder already exist there is no new plate. Confirm the quantity you need, re-sign the contract, and the item goes straight to production.

New customer — the eight steps

  1. Sign the contract The order is signed before artwork work starts, so the specification and the commercial terms are fixed first.
  2. Send artwork or a sample bag The design file, or the physical bag you want matched. Both are workable starting points.
  3. Sales confirms the details with you Size, material, color count, structure and quantity are agreed in writing — this is the specification the plate is built against.
  4. Technical review of the artwork Our technicians check whether that design can actually be produced on that structure, before any plate is cut.
  5. Proof from the plate maker We take the agreed artwork to our engraver and bring the proof back to you.
  6. You approve the proof Nothing is engraved until you confirm. This is the point where the final say on print sits with the buyer.
  7. The cylinder is engraved The plate maker produces the printing cylinder to the proof you approved.
  8. Mass production The item runs to the approved artwork and the confirmed specification.

A single contact through the route

One sales contact carries the order from artwork to shipment: they confirm the dimensions and details with you, take the artwork to the engraver, and bring the proof back to you. The technical review and the engraving are handled on our side — you are not asked to deal with the plate maker.

Where the buyer's decisions sit

Three points on the route are yours: the specification (size, material, print), the artwork itself, and the proof approval. Everything after the proof is factory work.

What can be customized

Four variables, and why the boundary has to be answered per product.

The four variables

Size Print color count Structure Material

Every product is open to customization on all four, but each one has its own limit on each one — because the film line, the bag line and the FIBC line are different equipment. A boundary that exists on one product may not exist on another.

Where the exact boundary is stated

On that product's page, and again in the quotation for the item you actually ask for. If you are not sure whether your specification is inside the boundary, send the drawing and we confirm it before anything is priced.

What is never assumed

Neither the color count nor the structure carries over from one product to another. A print that runs on film is not automatically available on a woven FIBC, and a size that exists as a bag is not automatically available as a roll. The confirmation is per item, in writing.

Minimum order quantities

Two thresholds — one for film, one for bags — and what makes an item custom.

Custom order minimums

Product family Minimum order
Film rolls & cold-stretch sleeve film 10 metric tons
Bags — valve, open-mouth, FIBC, foil & composite 20,000 bags

These are the thresholds for a custom item: a new size, a new structure, or printing that needs a cylinder.

Standard vs. custom

Standard sizes are not plated, so they follow a different minimum — that figure is stated on the product page. Anything printed, or made to a size that is not already running, is a custom item and follows the custom route on this page.

One custom specification, one run

Each custom specification needs its own plate, so two different print designs are ordered and produced as separate runs. Separately produced items can still be signed under one contract, so you keep a single commercial document while the line runs each specification on its own.

Plate, tooling and sample costs

Costed separately, itemized, and not credited back against volume.

Plate & tooling costs

Engraving and tooling are calculated separately from the product and listed as their own line item in the quotation, not folded into the unit price. They are borne by the buyer, and can be signed into the same contract as the goods so that there is one document for the order.

Deduction against volume

No deduction. The plate and tooling cost is not credited back against later volume orders. Budget it as a one-off cost per design, payable once, at the point the cylinder is made.

Samples and their freight

Samples are charged, and the freight is on the buyer's side. A sample is a produced item rather than a stock item, so it is quoted per request along with the courier cost to your address.

Before sampling: what to send

Four documents, and the reason each one is asked for.

The document list

  • Artwork and dimensions — the design file, plus the size, material and print colors you need
  • Printing authorization — your written instruction to print that artwork
  • Trademark registration certificate — proof that the brand being printed is yours
  • Business license — the company registration of the buying entity

Why the trademark and the license

We print brands we do not own. The authorization and the trademark certificate are what make it lawful to engrave your mark onto a cylinder at all, and the business license ties the order to a registered company. None of the three is paperwork for its own sake.

What this unlocks

With those four items the technical review can start and a sample can be produced. The plate is only cut after you have approved the proof, so nothing is committed to tooling before you have seen how the artwork reads on the material.

Frequently asked

Questions buyers ask before a custom order

The five points that decide whether a design goes to plate.

What is the minimum order quantity for a custom order?

10 metric tons for film rolls and cold-stretch sleeve film, and 20,000 bags for bag products — valve bags, open-mouth bags, FIBC bulk bags, foil bags and composite bags. Standard sizes that do not require a plate follow a different threshold, stated on the product page for that item.

Is the plate or tooling cost deducted from later volume orders?

No. Engraving and tooling are calculated separately from the product and listed as their own line item in the quotation, and they are not credited back against volume. They can be signed into the same contract as the goods, but they are a one-off cost per print design.

What do I need to send before you can make a sample?

Four things: the artwork together with the dimensions, material and print colors you need; a written printing authorization; the trademark registration certificate for the brand being printed; and the business license of the buying company. Without the authorization and the trademark certificate we cannot engrave your brand onto a cylinder.

Are samples free, and who pays the freight?

Samples are charged, and the freight is on the buyer's side. A sample is a produced item rather than a stock item, so it is quoted per request together with the courier cost to your address.

I am an existing customer placing a repeat order — do I pay for a new plate?

No. If the artwork and the printing cylinder already exist from the earlier order there is no new plate cost: confirm the quantity you need, re-sign the contract, and the item goes straight to production. A new plate is only needed when the artwork or the structure changes.

Next step

Send your artwork. Get the plate cost in one reply.

The design file plus the size, material and quantity is enough to start. You get back the plate and tooling cost as its own line, the minimum quantity for that item, whether the design can be produced on that structure, and what a sample and its freight will cost to your address.

Artwork reviewed before any plate is cut · Export team replies within 24 hours

Get my plate cost & MOQ
contact us
Name*
Email*
Message*
Verification Code*
Click to verify