Pallets of bagged cement, fertilizer, chemicals and minerals leave the plant protected on all five faces after a single machine cycle. That is the job stretch hood film is built for: a tubular PE film supplied on rolls, stretched open by an automatic hooding machine, drawn down over the load and then released so its own elastic recovery grips the pallet from the top edge to the base.
This is not a filling material and it is not a bag. It goes on after the bags are stacked and the pallet is built, and for most loads it is the only outer layer needed — the same sleeve that covers the sides also closes over the top.
Nothing in the process is heated. There is no shrink tunnel, no warm-up or cooling time, and no hot surface next to goods that may not tolerate heat. The film's own stretching and shrinking capability completes the wrap, which is why the cycle is a single downward stroke of the machine rather than a sequence of passes around the pallet.
In daily operation the rolls sit beside the hooding machine and are changed when a roll runs out; the hood is applied at the end of the palletizing line, before the pallet goes to the warehouse or the container. Plants that already run a hooding machine use the film as their standard export pack. Plants moving away from wrap and top sheets use it to take a manual step out of every pallet.
Because stretch hood packaging is one continuous sleeve rather than overlapping wrap turns, there are no loose film ends to catch on a container wall, on racking or on the next pallet in the stack. The load arrives with the same tight, square shape it had when it left the line.
| Feature | Benefit |
|---|---|
| Cold wrapping, no heat source | Lower energy cost, no shrink tunnel and safer operation next to bagged goods |
| Five-side protection in one cycle | Top and all four sides covered in one pass; replaces a stretch wrap pass plus a separate top cover |
| Strong elastic holding force | Load stays compressed and stable on the pallet through transport and stacking |
| High puncture and tear resistance | Reliable even with sharp-cornered or heavy loads |
| Dust, moisture and weather barrier | Keeps bagged goods protected in storage, in open yards and in transit |
| Custom width and gauge | Matched to your hooding machine and load |
| Industrial stretch hood performance | Consistent gauge and roll build keep an automatic sleeve line running steadily |
| Clear film option | Barcodes, labels and lot markings stay readable through the hood |
The film is co-extruded PE based on LLDPE, built as a tube rather than a flat sheet. Co-extrusion is the reason one film can be both tough and highly elastic: separate layers are given separate jobs — mechanical strength, elastic recovery, and the surface behaviour that lets the sleeve come off the spreader cleanly — instead of asking a single resin to do everything at once.
Tubular construction matters on the pallet, not just on the roll. The hood that goes over the load is a continuous closed loop of film, so there is no longitudinal seam running down one face of the pallet and no overlapping wrap turns that can unwind under load.
Elastic recovery is what actually holds the load. The resin balance decides how far the film can be stretched before application and how firmly it returns afterwards, which is what keeps a slightly uneven stack of bags from settling and working loose in transit.
Gauge is chosen against the job: denser, sharper-cornered loads concentrate stress at the corners of the pallet, while light, stable loads do not need the same amount of material to keep their shape. Width follows the pallet footprint and the machine rather than the other way round.
Additives adapt the film to where it will stand. UV stabilization is optional and is normally added for loads that spend time in open yards; pigments produce the opaque white and coloured versions used to identify a load or keep it out of view.
Co-extrusion is also what makes custom stretch hood film practical. Layer balance, folded width and gauge can be set for your machine and your load, so a plant running an unusual pallet size is not pushed into a stock specification that half fits.
| Item | Options |
|---|---|
| Material | Co-extruded PE (LLDPE-based) |
| Film type | Tubular stretch hood film, single-wound or gusseted |
| Thickness | 80–150 μm |
| Folded width | Custom design |
| Color | Clear, opaque white, colored |
| Printing | Optional, custom design |
| UV stabilization | Optional |
| Roll length / rolls per pallet | Custom design |
| Roll winding | Wound to suit the draw direction of your hooding head |
| Core | Sized to fit your machine's chuck |
| Gauge consistency | Held within the tolerance agreed for your order |
| Surface | Smooth plain film for even spreading on the spreader |
| Machine compatibility | Made to your hooding machine brand and model |
| Packaging | Rolls wrapped and palletized |
Jiangmei Packaging has been a stretch hood film manufacturer since 2008, working from a 60,000 m² plant in Changxing, Zhejiang, where film blowing, printing and converting run under one roof. The factory holds ISO 9001, ISO 14001 and ISO 45001 certification.
Blowing the film ourselves is what keeps the specification stable. Gauge, folded width and roll build are set on our own lines instead of being bought in from a third party, so a repeat order arrives with the same running behaviour as the first one.
We also make the bags that sit on the pallet — FFS film rolls, FFS tubular bags, open-mouth bags, valve bags, paper-plastic composite bags and FIBC bulk bags — which means a plant can buy the bag and the hood from one supplier and have both matched to the same filling and palletizing routine.
Our film and bags are exported to the Middle East, Latin America and other markets, so export packing and repeat supply are part of normal production rather than an exception.
For a buyer, the practical value is fewer hand-offs. When a hood does not sit right on a new pallet format, there is one technical contact who can look at the machine, the load and the film together instead of three suppliers pointing at each other.
Involving our technical team early makes specification easier. Tell us what you are packing, how your line or handling process works and what your machine expects, and we will help you match the right option in our range to your operation, including the settings that suit your conditions. If something does not run as expected, we work through the problem with you, suggest adjustments, and guide setup and first runs. Support continues after delivery, and we are glad to review requirements before you order.
No. Elastic recovery does the holding. The sleeve is stretched open mechanically, drawn down over the pallet and released, and the film wants to return to its original size — the load prevents it, so the film stays under tension and keeps the bags compressed. Because nothing is heated, there is no tunnel to run and no cooling stage before the pallet can be moved.
Folded width is set from the pallet footprint and the hooding machine together — the sleeve has to clear the widest part of the load and still come down to the base. The gauge decision comes from the load itself: weight, density and how sharp the bag corners are. Send the pallet dimensions, load weight and machine make, and we will come back with a custom stretch hood film specification for that combination rather than the nearest stock size.
We match the film to the machine you run rather than to a generic size. As a stretch hood film supplier we work from the make and model, the film width and gauge currently on the machine, and the pallet formats you handle. If a new machine is being installed, send the machine specification and the loads it will run, and the film can be specified before the line starts up.
That is where puncture and tear resistance matter most. Bag corners, pallet board edges and the corner of a dense mineral load all concentrate stress on a small area of film, and a hood that tears at one corner loosens across the whole pallet. An industrial stretch hood with the right gauge for the load resists that far better than a light wrap film, and the closed sleeve keeps its tension even when one corner is carrying the load.
Printing is optional and made to your artwork, and the film can be supplied clear, opaque white or coloured. Print is normally used for brand and load identification, and it is registered to your design so the hood carries the brand rather than a blank sheet.
Gauge, folded width and roll build are fixed once and repeated on every run. As the stretch hood film manufacturer we blow the film in-house, so a repeat order is produced on the same lines to the same specification instead of being sourced from whichever converter has stock. That is what lets an automatic hooding machine hold its settings across a full shift.