Introduction: Matching an FFS film roll to a packing line begins with forming tube geometry, then moves through thickness, roll-handling limits, and a sample run before order placement.
On an automatic FFS line, a roll that is slightly off can cause poor bag centering, weak seals, short roll runs, and extra changeovers. Work backward from the forming tube, bag length, gusset depth, fill drop, seal window, and unwinder limits. Then give those parameters to your supplier for a trial roll. This sequence turns published width and thickness limits into a written machine-fit specification.
The forming tube is the starting point. Film enters the collar, wraps around the tube, and becomes a continuous tube before the bottom seal closes it. Tube circumference controls how much film the machine needs across the web. Bag length is set by the sealing jaw stroke and machine cycle. If you order width without tube measurements, the roll can look correct on paper and still sit poorly on the collar, pull off-center, or seal with a skew. Before approving a sample roll, compare tube diameter, current roll width, bag length, gusset depth, fill drop, and seal dwell on the same machine.
For a plain tube, lay-flat film width is about half the forming tube circumference. Adjust that figure for collar clearance, seam allowance, and the machine's film path. A 600 mm circumference points toward roughly 300 mm lay-flat before those allowances; a 1,000 mm circumference points toward roughly 500 mm. The practical figure comes from the machine builder's tube drawing and the film supplier's winding data. Record tube diameter, bag width, and current roll width together. The disclosed 400–760 mm width range sets the available limits, but the exact roll width belongs in the written order specification.
Gussets are side folds that let the finished bag open wider without forcing a larger forming tube. They help when a powder or pellet load needs more room but the machine's tube geometry is fixed. The width calculation uses A + 2D logic: set the finished body width A, add the gusset depths D that create side volume, and keep the ordered width within 400–760 mm. Gusset depth up to 100 mm supports this adjustment. Deeper gussets can improve fill room and pallet shape, but they also change how the film folds and tracks. Review bag length, fill drop, and seal position with the sample.
Thickness selection depends on the material and the seal conditions on the line. A bag that runs well on light flakes can fail on dense resin pellets because the same bag volume carries more weight and hits the bottom seal with more energy. Bulk density, particle shape, drop height from the filling spout, and dust at the seal area all affect film demand. Dense pellets, abrasive minerals, and high drop heights usually call for a heavier gauge within 70–240 μm. Light powders, short drops, and gentle handling can use a lower gauge if the bag still has enough body for pallet stacking and transport. Seal conditions set the other side of the choice. A high-speed FFS line gives the seal jaws a short dwell, so the film must reach sealing temperature and weld cleanly within that window. Heavier film needs more heat or longer dwell to seal through the full thickness; lighter film can seal quickly but may not hold up to fill impact. Three-layer co-extruded polyethylene with LLDPE, HDPE, and functional additives lets a polyethylene film manufacturer balance toughness, seal response, and surface behavior. The practical thickness is the one that seals at your line speed and survives the drop into the bag. Run a sample roll on your machine to confirm that combination. Food-contact or regulated transport approvals are handled case by case.
A continuous FFS line depends on steady unwinding as much as on film strength. An outside diameter up to 1,500 mm allows long runs and fewer roll changes, but a large, heavy roll stores more inertia. The unwinder brake, dancer, and tension control must manage that mass from the first meter to the last. A roll that is too heavy for the shaft or too large for line-side handling can turn a planned roll change into a stall. Match roll diameter and weight to shaft capacity, floor space, and lifting method. Then set roll length so the change interval fits the production shift. Core size and wind direction are just as practical. The core must fit the machine shaft without shims, and the film must unwind in the direction the machine expects. A core that is correct in diameter but wrong in wall thickness can slip under torque; a roll wound in the reverse direction will not feed the collar correctly. Pallet pattern controls storage density, fork truck access, and how the roll is presented to the line. Before ordering, put core size, wind direction, roll length, roll weight, and pallet pattern into the written specification. That gives the FFS film roll supplier a clear winding brief instead of a generic roll.
Start with the forming tube, then set bag length and gusset depth. Choose a thickness that matches fill drop, bulk density, and seal window. Finish by matching roll diameter, core, roll weight, and pallet pattern to the unwinder and the people who change the roll. This sequence produces a machine-fit brief you can send to a supplier for a sample and a written quote. Jiangmei Packaging is an FFS film manufacturer supplying tubular FFS film rolls in width 400–760 mm, thickness 70–240 μm, gusset up to 100 mm, and outside diameter up to 1,500 mm, with custom orders starting at 10 metric tons. Send tube geometry, bag length, fill material, seal dwell, core size, and target roll weight so the sample roll and order specification can be reviewed with you.
A: Forming tube circumference sets the base lay-flat film width, which is roughly half the circumference before collar clearance, seam allowance, and gusset additions. Use the machine tube drawing and A + 2D width logic, then confirm final roll width within the disclosed 400–760 mm range and on a sample run.
A: Base the choice on bulk density, fill drop height, particle shape, seal dwell, and seal temperature. Dense pellets, abrasive minerals, and high drops usually need a heavier gauge within 70–240 μm. Light powders and short drops can use a lower gauge if the bag still handles stacking and transport. Run a trial roll on your line to confirm the choice.
A: Confirm outside diameter against the unwinder limit, up to 1,500 mm; core size against the machine shaft; wind direction against the film path; and roll length and roll weight against shaft capacity and planned change intervals. Also agree on pallet pattern for storage and line-side handling, then put every detail in the written order.
PMMI, The Association for Packaging and Processing Technologies
Plastics Industry Association | Advocacy & Sustainability